Max M9 v2 - ClockWorkMod v6.0.3.1
2 posters
Page 1 of 1
Max M9 v2 - ClockWorkMod v6.0.3.1
IMPORTANT: This is a touch recovery and does contain a bug The menu disappears just press and hold on screen and move up or down as if you were scrolling and menu will reappear. be very careful not just to touch when no menu is displayed as it will action whatever option you would have touched if you could see the menu.
Installation
Download includes flashtool, recovery (original & CWM), and drivers
1. Run RKAndroidTool.exe
2. Enter flashmode on your tablet.
From Powered Off Pres & hold esc button while inserting USB keep holding esc button and press and hold power button until RKAT says loader mode.
3. Click Run
Tab should reboot and start as normal to Android OS
4. Install a Terminal App to Rooted Tab
5. In Terminal App Enter su reboot recovery
Note: I know it has been stated that there is no button combo to enter recovery on the M9 but I think it may be a timing trick with the buttons as I'm sure I did it by accident but have not been able to replicate thus far.
This does need some proper testing and all comments are welcome
Downloads
http://www.mediafire.com/?c52pyqk7m5va53g
Installation
Download includes flashtool, recovery (original & CWM), and drivers
1. Run RKAndroidTool.exe
2. Enter flashmode on your tablet.
From Powered Off Pres & hold esc button while inserting USB keep holding esc button and press and hold power button until RKAT says loader mode.
3. Click Run
Tab should reboot and start as normal to Android OS
4. Install a Terminal App to Rooted Tab
5. In Terminal App Enter su reboot recovery
Note: I know it has been stated that there is no button combo to enter recovery on the M9 but I think it may be a timing trick with the buttons as I'm sure I did it by accident but have not been able to replicate thus far.
This does need some proper testing and all comments are welcome
Downloads
http://www.mediafire.com/?c52pyqk7m5va53g
vitha- Senior Member
- Posts : 373
Join date : 2012-10-28
Re: Max M9 v2 - ClockWorkMod v6.0.3.1
You may need to change the address where the recovery has been flashed to. In the area just to the right of the checkbox is an address 00010000. Try changing this value to 00014000 and then flash recovery again.
Reboot recovery again. You should get CWM menu with one or the other address.
Reboot recovery again. You should get CWM menu with one or the other address.
vitha- Senior Member
- Posts : 373
Join date : 2012-10-28
Re: Max M9 v2 - ClockWorkMod v6.0.3.1
Hi, I have loaded the "Update#79 20130516 4.2.2 V2 multi feature bug fixed" rom, and when trying to reboot into recovery got the dead android. I Then tried loading this as per your instructions - tried both addresses, and still get the problem. Interestingly, I was booting to recovery using an app from the store, rather then terminal. If I use a terminal and "su reboot recovery" I get "Segmentation fault", and no reboot.
Any help would be much appreciated.
Thanks in advance....
Any help would be much appreciated.
Thanks in advance....
pebrey- New Member
- Posts : 1
Join date : 2013-06-16
Re: Max M9 v2 - ClockWorkMod v6.0.3.1
Check this one out https://vitha.forumotion.com/t128-cwm-based-recovery-for-pipo-m9#211
I forgot if you getting a dead android you might have flashed to wrong location, Parameter states 0x00014000 . Nan changed location on newer firmware
I forgot if you getting a dead android you might have flashed to wrong location, Parameter states 0x00014000 . Nan changed location on newer firmware
vitha- Senior Member
- Posts : 373
Join date : 2012-10-28
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum
|
|